Planning · 8 minute read

Window Replacement Council Approval – When NSW Homes Need It and When They Don’t

  • 10+ years on the toolsSydney and the Central Coast
  • Licence 399743CVerifiable on the NSW register
  • $10M public liabilityInsured with NRMA
  • Cert IV BuildingPlus Cert III Carpentry
  • 5/5 on GoogleFrom 15+ reviews

The short answer

Williamson Builds’ short answer: in NSW you can usually replace a window like for like without council approval, as long as the opening stays the same size and the house is not on bush fire prone land, heritage listed or in a heritage conservation area. Make the opening bigger, add a new window or turn a window into a door, and the work needs a complying development certificate or a development application before it starts.

Same size opening
Usually exempt
New or bigger opening
CDC or DA first
Bush fire prone land
Not exempt
Heritage
Ask council first

Do You Need Council Approval to Replace Windows in NSW?

Usually not. Replacing an external window in the same opening is exempt development under the NSW planning code, so it needs no approval from council or a certifier.

The rule sits in the State Environmental Planning Policy (Exempt and Complying Development Codes) 2008, under minor external building alterations. It lists “the replacement of an external window, glazing areas or a door (other than those on bush fire prone land)” as a minor, non-structural alteration. The NSW Planning Portal’s page on exempt development confirms that exempt work needs no planning or construction approval, provided it meets every standard in the code. For a window, the standards say the work must:

  • not make a new opening or alter the size of any opening in a wall or roof
  • not reduce the existing fire resistance level of a wall
  • not affect any existing fire resisting components of the building
  • not affect the means of escape from the building in an emergency
  • meet the Building Code of Australia and be installed to the manufacturer’s specifications

What counts as a like for like window replacement?

A new window in the old opening, with the opening left the same size.

The code’s test is the opening, not the frame. On a standard block it does not ask for the same frame material, so a timber window can be replaced with aluminium in the same opening and still be exempt. The limit is the word non-structural. If the lintel or the studs around the window have to be rebuilt, or the opening changes at all, you are outside the exemption.

Does replacing an external door follow the same rule?

Yes. The same clause covers the replacement of a door, with the same conditions.

A new front or back door in the existing frame opening is exempt on the same terms. A wider door, or a door where a window used to be, is a change to the size of the opening and is treated differently.

When Does a Window Replacement Need Council Approval?

When the opening changes, when the land is bush fire prone, or when the house is heritage listed or in a heritage conservation area.

Any one of these takes a window job out of exempt development:

  • A new or resized opening. The code rules out making an opening or altering its size, whether it is a doorway, a window or a skylight.
  • Bush fire prone land. The exemption for replacing windows and doors excludes it.
  • Heritage. The exemption does not apply on or in a heritage item, a draft heritage item, or a heritage conservation area.
  • Structural work. The exemption is for non-structural alterations only.

Can you change a window to a door without council approval?

No. Cutting a window down to a door alters the size of the opening, so it is not exempt.

The usual path is a complying development certificate. The NSW Planning Portal’s page on home renovation as complying development says some external alterations to existing houses qualify. If the job does not meet those standards, it needs a development application to Central Coast Council. Our guide to removing a load-bearing wall explains the difference between the two, and the same structural questions apply when an opening gets wider.

What are the privacy rules for a new window?

Under the complying development code, a new window that looks over a side or rear boundary may need a privacy screen.

The Housing Alterations Code in the same policy requires a privacy screen on any part of a new window lower than 1.5 metres above the floor where the window is in a habitable room with a floor more than 1 metre above ground, has a sill lower than 1.5 metres, and faces a side or rear boundary less than 3 metres away. The same test applies to a room with a floor more than 3 metres above ground where the boundary is 3 to 6 metres away. Bedroom windows of 2 square metres or less are excluded.

What if Your Home Is on Bush Fire Prone Land?

Then replacing a window is not exempt development, and the approval will look at the bush fire attack level of your block.

Many Central Coast streets back onto bush, so check this first. The NSW Rural Fire Service has an online tool to check whether your land is bush fire prone, and says the section 10.7 planning certificate from council confirms it.

The RFS guide to building on bush fire prone land explains why windows get so much attention. It describes glazing as highly susceptible to radiant heat and flying debris, and says 85% of houses are lost from ember attack. Windows need glass thick enough to protect against the heat of a fire, metallic screening may be needed to keep embers out, and the type of construction depends on the Bush Fire Attack Level determined for the property. Central Coast Council also notes that some properties in high-level bush fire prone areas are restricted from complying development, which leaves a development application.

What if the House Is Heritage Listed or in a Conservation Area?

Ask council before any work starts, because the exemption for replacing windows does not apply.

Central Coast Council says properties listed in Schedule 5 of the Central Coast Local Environmental Plan 2022 need development approval for development work. Its page on heritage exemptions explains that owners can seek an exemption from formal approval for minor works or maintenance that will not harm the heritage significance of the property, such as minor repairs using the same materials and finishes. Owners must lodge the Heritage Exemption Form and receive written approval from council before beginning. On a heritage house, plan to repair the original windows or match them closely.

Custom window bench with VJ panelling, a Williamson Builds job at Wyoming on the Central Coast
Window joinery on a Williamson Builds job at Wyoming.

What Safety Rules Apply to a Replacement Window?

Exempt work still has to meet the Building Code of Australia, and the rule most often missed is fall protection on upstairs bedroom windows.

Under Part 11.3 of the NCC 2022 Housing Provisions, a bedroom window needs protection where the floor is 2 metres or more above the surface beneath and the opening is lower than 1.7 metres above the floor. The openable part must have a device that restricts the opening, or a screen with secure fittings. Either must stop a 125 mm sphere passing through and resist an outward force of 250 newtons. In other rooms the trigger is a floor 4 metres or more above the surface beneath, and the answer is a barrier at least 865 mm high. A new upstairs bedroom window with a low sill and no restrictor does not comply, however good it looks.

What about units and rental properties?

Strata buildings have their own window lock rule, and the windows are often common property.

NSW’s safety rules for strata common property require a safety lock where the lowest part of the window is within 1.7 metres of the inside floor and that floor is 2 metres or more above the ground outside. The lock must stop the window opening more than 12.5 cm. The owners corporation pays to install and repair window locks unless the by-laws say otherwise. In a rental, NSW’s page on window, deck and balcony safety says landlords must allow window safety devices if a tenant asks. In a unit, replacing a window also involves the owners corporation, and our guide to strata bathroom renovation approval sets out how NSW sorts strata work into cosmetic, minor and major.

What standard should the window itself meet?

AS 2047, which the Australian Glass and Window Association describes as the mandatory minimum specification for windows and doors used in Australia.

AGWA’s compliance guidance says AS 2047 includes compliance with AS 1288, the standard for glass in buildings, and that for housing the purchaser nominates the window ratings and the exposure when ordering. That matters on this coast, where an exposed headland and a sheltered valley block call for different wind ratings. Ask the supplier for the compliance certificate and keep it with the house records.

Who Can Replace Windows in NSW?

A licensed contractor, for any job worth more than $5,000 in labour and materials including GST.

NSW issues several licences that cover windows. Glazing work includes installing prefabricated or pre-assembled windows. Carpentry work covers fixing components such as windows and doors. General building work includes all of the trade categories, which matters when the job turns out to involve rot in the frame, a new lintel or a wider opening. Our guide to choosing a carpenter or a builder covers where that line sits, and you can check any licence on the Service NSW licence check.

What about asbestos and lead paint around old windows?

Assume both are possible in an older house until they are ruled out.

The NSW Government’s asbestos site says a property built or renovated before 1990 probably has asbestos-containing materials. Its page on walls says asbestos can be found in sealants and putties used in places like windows, and that eaves were made from bonded asbestos sheeting until the mid 1980s. The planning code also bars exempt work from removing more than 10 square metres of non-friable asbestos, or any friable asbestos, unless a licensed asbestos removalist does it. The Australian Government’s guide to lead in house paint says paints with high levels of lead were used in many Australian houses before 1970, and names window frames among the places it is found. Both are reasons to have old frames tested before anyone sands or cuts them.

Do new windows need a BASIX certificate?

Only where the work is part of alterations and additions costing $100,000 or more.

The NSW Planning Portal says BASIX applies to alterations and additions at that value, and that the certificate is submitted with a development application or complying development certificate. Performance still matters on a smaller job. The Australian Government’s YourHome guide to glazing says up to 40% of a home’s heating energy can be lost and up to 87% of its heat gained through windows.

So Do You Need Approval to Replace Your Windows?

Same opening, standard block, no heritage listing: no approval, but the window still has to meet the building code. Bigger opening, bush fire prone land or heritage: get the approval path confirmed before you order.

Windows are made to order, so an approval problem found after the order is placed is a hard one to fix. Three checks come first: the bush fire map, the heritage listing and whether the opening is changing. A fourth is worth making on an older house, which is what the old frame is hiding. Water gets in at the sill long before the paint shows it, and a rotted sill plate is a repair to do while the wall is open.

Williamson Builds replaces windows and external doors across all of the Central Coast, with Newcastle and Sydney by arrangement for larger jobs, under general building licence 399743C with $10 million in public liability cover. This guide is general information for NSW and is not planning or legal advice. Rules change, so check the legislation and the council pages linked above, or ask Central Coast Council, before relying on it for your block.

Written by

Hamish Williamson

Director and licensed builder, Williamson Builds, licence 399743C

Hamish has spent more than ten years on the tools, including high-end residential work in Dee Why and Annandale before starting Williamson Builds on the Central Coast. He checks every guide on this site before it goes up.

NSW licence 399743C · Certificate III in Carpentry · Certificate IV in Building and Construction. Search the licence number on the Building Commission NSW register.

Last reviewed 16 October 2026

More about Hamish and Williamson Builds

GET MY FREE QUOTECall 0420 221 420

Hamish Williamson, director and licensed builder at Williamson Builds

Start here

Tell Us About Your Job

A sentence and a couple of photos is enough for us to know how to help. If someone else is the better call, we’ll say so in the reply.

  • Licence 399743C
  • Public liability insured
  • 5/5 from 25+ Google reviews

Get a free quote

Name

We reply within one working day. No obligation, no sales call.

Call 0420 221 420