Repairs · 7 minute read

Sagging Floors – What Causes Them and When to Call a Builder

  • 10+ years on the toolsSydney and the Central Coast
  • Licence 399743CVerifiable on the NSW register
  • $10M public liabilityInsured with NRMA
  • Cert IV BuildingPlus Cert III Carpentry
  • 5/5 on GoogleFrom 15+ reviews

The short answer

Floors usually sag because something in the subfloor has lost strength or support: bearers and joists weakened by damp, rot or termites, stumps that have sunk or decayed, or framing cut or overloaded during past work. A floor that dips, bounces or feels soft needs the subfloor inspected before anyone quotes, because the cause decides the repair.

Most common cause
Damp, rot or termites under the floor
Signs it is getting serious
Soft spots, sticking doors, new cracks
Subfloor repair over $5,000
Licensed contractor required
Like-for-like restumping
Can be exempt from approval

What Causes a Sagging Floor?

A sagging timber floor almost always means something underneath has lost strength or support, and water is behind most of it. Damp feeds rot and termites, and both eat away at the bearers, joists and stumps that hold the floor up.

The National Construction Code’s explanatory notes on subfloor ventilation put it plainly: ground moisture rising into the subfloor space can create a damp environment that encourages timber rot, fungus growth and termite activity. The timber industry’s technical guide on moisture-affected timber-framed construction says a moisture content of 20% or above is conducive to decay. On the Central Coast, where many older homes sit on timber subfloors close to the water, these are the causes that turn up most:

  • A damp, poorly ventilated subfloor: blocked vents, garden beds built up against the walls, or stormwater running under the house.
  • Rot in bearers and joists: often below a bathroom or laundry where a leak has gone unnoticed for years.
  • Termite damage: timber that looks sound from outside but is hollow inside.
  • Sunk, rotted or rusted stumps: the floor follows the stump down, so the dip sits over one point.
  • Framing cut or overloaded during past work: joists notched for pipes, a wall removed without a beam, or a heavy bath or island bench added over a long span.

Why is my floor sagging in one spot?

A dip in one spot usually points to one failed member below it: a stump that has dropped, a joist that has rotted or been cut, or a leak that has soaked one area.

A floor that sags across a whole room is more often a bearer problem or a run of tired stumps. A dip right outside the shower or beside the toilet is a strong hint that a slow leak has been wetting the framing. Fixing the floor without fixing that leak just starts the clock again, which is why our guide to mould in a rental property spends so much time on finding water.

When Should You Worry About a Sagging Floor?

Worry when the floor feels soft or spongy, when the dip is getting worse, or when doors, walls and cornices start moving with it. A slight, old dip that has not changed in years is a different conversation from a soft patch that appeared this winter.

These are the signs that the problem is active and needs a builder to look underneath:

  • A soft or springy patch that gives underfoot, especially near a wet area.
  • Doors that start sticking or no longer latch, and gaps opening above or below them.
  • New cracks in plaster, cornices or tiles, or skirting boards pulling away from the floor.
  • A damp, musty smell coming up through the floor or from the subfloor vents.
  • Mud tubes or hollow-sounding timber around stumps and framing, which can mean termites.

Is a sagging floor dangerous?

It can be, once the timber underneath is rotted badly enough to give way, so keep weight off any area that feels soft until it has been checked.

Most sagging floors are a slow problem, but rotted bearers and joists do fail. Keep heavy furniture, full baths and foot traffic off a soft spot, and do not cut into the floor or prop it up yourself. Structural repair is licensed work for good reason.

Is a bouncy floor the same as a sagging floor?

Not always. Some bounce is normal for a timber floor laid over joists, but bounce that is new or getting worse is a warning sign.

The WoodSolutions technical guide to timber flooring notes that strip timber floors laid over joists or battens generally have more spring underfoot. A floor that has always felt lively is usually just that. Bounce that arrives with a dip, a soft patch or a smell is the subfloor telling you something has changed.

What Should You Send a Builder About a Sagging Floor?

Send photos of the dip and the room, a note of when you first noticed it, whether it changes with the weather, and any pest or building reports you already have. That is enough for a builder to know what to look for on site.

You do not need to crawl under the house to be useful. From outside you can usually see whether the subfloor vents are blocked by soil, plants or stored items, and whether water pools along the walls after rain. The WoodSolutions guide to moisture-affected framing makes the same point for owners: make sure all ventilation points are clear of debris and dirt. Note it, photograph it, and leave the structural judgement to the person who will be signing the scope.

If the house had a termite inspection in the past, find the report. CSIRO’s guide to managing termites says termites can cause extensive damage if left undetected, that most attacks start from the soil, and that regular inspections, at least annually, are needed. A gap in that history changes how carefully the framing gets checked.

How Is a Sagging Floor Fixed?

A sagging floor is fixed in order: stop the water, deal with any termites, replace or reinforce the failed bearers, joists and stumps, and only then relevel and repair the floor itself. Packing a dip without fixing the cause rarely lasts.

Termite treatment is a job for a licensed pest controller, and it comes before new timber goes in. The structural repair then depends on what failed. Rotted or eaten members are cut out and replaced, stumps are replaced with new ones, and the floor is brought back to level gradually. Where the subfloor is being rebuilt, it is worth building it to today’s code rather than repeating the old detail.

For new work, the NCC 2022 Housing Provisions set a minimum ground clearance of 150 mm under a suspended floor where no termite inspection or management system is required, and 400 mm where termite inspection is required, along with minimum areas of ventilation openings. Part 3.4 of the same provisions covers termite risk management and calls up AS 3660.1 for termite management systems. An older house may not meet those numbers, and a builder can tell you which improvements are practical on your site.

Does restumping need council approval?

Often not. Restumping or repairing foundations without raising the house can be exempt development in NSW, as long as the work is like-for-like and meets the conditions.

NSW Planning’s fact sheet on remedial building work quotes the Codes SEPP, which lists restumping or repairing structure foundations without increasing the height of the structure as a minor external alteration. The fact sheet says the work must not permanently alter the load bearing capacity of the building, must reinstate the element to its intended structural capacity and must not change the original design. It also notes that exempt work does not apply to heritage items or heritage conservation areas, so check your address first.

Who can repair a sagging floor in NSW?

A licensed contractor must carry out residential building work worth more than $5,000 in labour and materials, and repairing a dwelling counts.

NSW’s page on general building work says residential building work includes repairing a dwelling, and that a contractor licence is needed for work over that threshold. Subfloor jobs grow once the floor is opened, so a builder who writes a clear scope, with what happens if more rot turns up, saves an argument later.

Does a Sagging Floor Matter in a Rental or a Sale?

Yes. In a NSW rental, floors and supporting structures that are rotted or significantly damp can mean the property is not structurally sound, and in a sale a sagging floor is one of the first things a building inspector notes.

Section 52 of the Residential Tenancies Act 2010 says a rental is only structurally sound if its floors, walls, supporting structures and foundations are in a reasonable state of repair, are not subject to significant dampness and are not liable to collapse because they are rotted or otherwise defective. Our guide to rental property minimum standards in NSW covers what that means for landlords and property managers.

For buyers and sellers, NSW’s page on pre-purchase inspection reports notes that a building report won’t say whether termites are still around, which is why a separate pest inspection matters. If you are selling, a floor repaired with a written scope and photos reads very differently in a buyer’s report than one that has been patched. See our guide to repairs before selling a house.

So What Should You Do About a Sagging Floor?

Get the subfloor looked at before anything is quoted, fix the water and any termite activity first, and then repair the structure properly. A dip is a symptom. The job is whatever caused it.

Most sagging floors on the Central Coast are slow, fixable problems when they are caught early. Left alone, a damp subfloor keeps feeding rot and termites, and the repair grows with every wet winter.

Williamson Builds repairs subfloors, stumps and timber floors across all of the Central Coast, with Newcastle and Sydney by arrangement for larger jobs, under builder’s licence 399743C with $10 million in public liability cover. See our page on home repairs and maintenance for the jobs we take on. This guide is general information for NSW, so check the linked sources for the current rules that apply to your home.

Written by

Hamish Williamson

Director and licensed builder, Williamson Builds, licence 399743C

Hamish has spent more than ten years on the tools, including high-end residential work in Dee Why and Annandale before starting Williamson Builds on the Central Coast. He checks every guide on this site before it goes up.

NSW licence 399743C · Certificate III in Carpentry · Certificate IV in Building and Construction. Search the licence number on the Building Commission NSW register.

Last reviewed 29 October 2026

More about Hamish and Williamson Builds

GET MY FREE QUOTECall 0420 221 420

Hamish Williamson, director and licensed builder at Williamson Builds

Start here

Tell Us About Your Job

A sentence and a couple of photos is enough for us to know how to help. If someone else is the better call, we’ll say so in the reply.

  • Licence 399743C
  • Public liability insured
  • 5/5 from 25+ Google reviews

Get a free quote

Name

We reply within one working day. No obligation, no sales call.

Call 0420 221 420