Flooring · 6 minute read

Engineered vs Solid Timber Flooring – Which Suits a Central Coast Home?

  • 10+ years on the toolsSydney and the Central Coast
  • Licence 399743CVerifiable on the NSW register
  • $10M public liabilityInsured with NRMA
  • Cert IV BuildingPlus Cert III Carpentry
  • 5/5 on GoogleFrom 15+ reviews

The short answer

The subfloor usually decides between engineered and solid timber flooring before taste does. Solid tongue and groove boards suit a house on bearers and joists, where they can be nailed straight to the frame and sanded back for decades. Engineered boards suit concrete slabs, apartments and floors laid over an existing floor, because their layered build moves less as the humidity changes.

Solid boards
Best over joists
Engineered boards
Best over slabs and in units
Both
Real timber that moves with moisture
Strata units
Hard floors need approval

What Is the Difference Between Engineered and Solid Timber Flooring?

Solid flooring is one piece of timber through its full thickness, while engineered flooring is a layer of real timber bonded over a base of plywood or timber layers. Both have a real wood surface. What sits under that surface is what changes how they behave.

The Australasian Timber Flooring Association, the industry’s peak body, describes engineered flooring as having a lamella or veneer of solid timber, generally over base layers of plywood or timber blocks. It says engineered flooring was designed to significantly reduce the amount of width movement in boards, while keeping a real wood surface. The layers below run in opposing directions, so each one holds the next in check.

Solid tongue and groove boards have no such help. They are the traditional Australian floor, usually hardwood, laid board by board, then sanded and coated on site. That on-site finish is part of the appeal. It is also why a solid floor takes longer to finish and why the house has to be empty while it is done.

  • Solid: one species through the whole board, usually nailed to joists or battens, sanded and coated after it is laid.
  • Engineered: a timber top layer on a stable base, usually pre-finished, then glued down or laid as a floating floor.
  • Not the same as laminate or hybrid: those have a printed or vinyl surface, not timber, and are a different conversation.

Which Timber Floor Copes Better With Central Coast Humidity?

Engineered boards move less across their width, but both types are real timber and both swell and shrink with the moisture in the air. The installation decides more than the product does.

ATFA’s guide to what to expect from a solid timber floor explains that timber flooring is hygroscopic: its moisture content and dimensions change with how dry or moist the air is. Solid boards expand or shrink across their width, and lengthwise movement is negligible. It says providing the right movement allowance for the floor, in the place it is laid, is a must and not an option.

That matters on the coast, where a house can sit damp through a wet summer and dry out in a westerly. WoodSolutions’ timber moisture guide says timber should be installed within plus or minus 2% of the moisture content it will settle at in service, and that typical Australian interiors range from 8 to 14%. Boards laid too wet shrink and gap. Boards laid too dry, or with no room at the edges, swell and push up.

Why does the subfloor matter so much?

Because a damp space under the house reaches the boards from below.

ATFA notes that moist subfloor spaces can cause boards to cup, and WoodSolutions points to the National Construction Code’s requirement for ventilation in enclosed subfloor spaces. Plenty of older Central Coast houses sit on bearers and joists over ground that stays wet, with vents that have been blocked by garden beds or a later deck. Before a new floor goes in, it is worth a look underneath. If the floor frame is soft or the space is wet, that is a subfloor repair to sort out first, because new boards over a damp, failing frame will not last.

Can Engineered Timber Flooring Go Over Joists, or Only Over a Slab?

Solid structural boards are the natural choice over joists, and engineered boards are the natural choice over a concrete slab or an existing floor. Each can be made to work the other way, but it adds layers and cost to the job.

ATFA’s solid flooring guide says structural boards, at least 19 mm thick, are generally at least 900 mm long when laid on joists or battens, and should span at least two joists. The boards are the floor. Nothing sits between them and the frame. That is why solid boards are the usual way to replace a worn floor in a house on bearers and joists.

Engineered boards are thinner and rely on what is under them. ATFA’s guide to engineered, laminate and bamboo floors says engineered flooring may be glued to the subfloor or installed as a floating floor, where the boards are fixed to each other and not to the subfloor. That suits a slab, which is why engineered boards are common in newer homes and units. ATFA also notes that any timber glued to concrete can sound hollow under some boards, so a flat, dry slab and the right adhesive matter.

Can You Sand an Engineered Timber Floor Like a Solid One?

Usually yes, but fewer times, because only the top layer of an engineered board is timber you can sand into. A solid board can be sanded down close to its tongue and groove.

ATFA says re-sanding and recoating is an acceptable way to bring a floor back, with some reduction in the life of the floor each time, and that engineered flooring can also be sanded and coated on site. How many times depends on how thick the timber top layer is, so ask for that figure before you buy. ATFA also notes that engineered boards finished in hardwax oil can be rejuvenated and are easier to repair.

For a family home you plan to stay in for decades, that difference counts. For a unit you might sell in five years, it rarely does.

Which is harder wearing?

The species and the coating decide the wear, not whether the board is solid or engineered.

A spotted gum surface is a spotted gum surface whatever sits under it. ATFA notes that much engineered flooring has a top layer at least 2.5 mm thick, which helps it resist denting. Whichever you choose, dents from furniture and grit under shoes are the usual damage, and felt pads and a doormat do more than the board type.

Do You Need Approval to Put Timber Floors in a Strata Unit?

Yes. In NSW, installing or replacing hard flooring in a strata unit is a minor renovation, which needs the owners corporation’s approval. Carpet does not.

NSW’s strata renovation rules list installing or replacing wood, tile or other hard flooring, including removing carpets, as a minor renovation, while laying carpet is cosmetic work that needs no approval. Minor renovations need more than 50% of the votes cast at the meeting. If you are installing flooring, the application should include an acoustic certificate to show sound insulation. A committee that refuses must give written reasons within three months, and the owners corporation keeps a record of approved minor renovations for 10 years.

This is where engineered boards on an acoustic underlay usually win in a unit: they are thinner, they float or glue over the slab, and the underlay can be chosen to meet the scheme’s by-laws. Check the by-laws before you choose a product. Some schemes set their own acoustic standard. If the floor is part of a bigger job, our guide to strata bathroom renovation approval covers the major renovation vote.

So Should You Choose Engineered or Solid Timber Flooring?

Choose solid boards for a house on bearers and joists you plan to keep, and engineered boards for a slab, a unit or a floor laid over an existing one. Then spend as much care on the subfloor and the edges as on the timber.

On the Central Coast that splits roughly by the age of the house. Older homes on piers suit solid hardwood nailed to the joists, and a sound frame under a worn floor often only needs new boards. Newer homes on slabs, townhouses and units suit engineered boards, which go down faster and move less. Where a renovation is opening up the room anyway, it is the right time to decide, and our page on home renovations covers how the trades fit together.

Williamson Builds lays timber and engineered flooring, along with skirting and architraves, across all of the Central Coast under builder’s licence 399743C. Every floor is fitted to the house as it stands, which on an older house usually starts underneath it.

Written by

Hamish Williamson

Director and licensed builder, Williamson Builds, licence 399743C

Hamish has spent more than ten years on the tools, including high-end residential work in Dee Why and Annandale before starting Williamson Builds on the Central Coast. He checks every guide on this site before it goes up.

NSW licence 399743C · Certificate III in Carpentry · Certificate IV in Building and Construction. Search the licence number on the Building Commission NSW register.

Last reviewed 15 October 2026

More about Hamish and Williamson Builds

GET MY FREE QUOTECall 0420 221 420

Hamish Williamson, director and licensed builder at Williamson Builds

Start here

Tell Us About Your Job

A sentence and a couple of photos is enough for us to know how to help. If someone else is the better call, we’ll say so in the reply.

  • Licence 399743C
  • Public liability insured
  • 5/5 from 25+ Google reviews

Get a free quote

Name

We reply within one working day. No obligation, no sales call.

Call 0420 221 420